`timescale 1ns / 1ps

`include "radar_params.vh"

module radar_receiver_final (
    input wire clk,           // 100MHz    
	 input wire reset_n,
    
	// ADC Physical Interface (LVDS Inputs)
    input wire [7:0] adc_d_p,        // ADC Data P (LVDS)
    input wire [7:0] adc_d_n,        // ADC Data N (LVDS)
    input wire adc_dco_p,            // Data Clock Output P (400MHz LVDS)
    input wire adc_dco_n,            // Data Clock Output N (400MHz LVDS)
    // Audit F-0.1: AD9484 OR (overrange) LVDS pair
    input wire adc_or_p,
    input wire adc_or_n,
	 output wire adc_pwdn,

    // Chirp counter from transmitter (for matched filter indexing)
    input wire [5:0] chirp_counter,
    // Frame-start pulse from transmitter (CDC-synchronized, 1 clk_100m cycle)
    input wire tx_frame_start,

    output wire [31:0] doppler_output,
    output wire doppler_valid,
    output wire [4:0] doppler_bin,
    output wire [`RP_RANGE_BIN_WIDTH_MAX-1:0] range_bin,  // 9-bit
    
    // Raw matched-filter output (debug/bring-up)
    output wire signed [15:0] range_profile_i_out,
    output wire signed [15:0] range_profile_q_out,
    output wire range_profile_valid_out,

    // Decimated 512-bin range profile (for USB bulk frames / downstream consumers)
    output wire [15:0] decimated_range_mag_out,
    output wire decimated_range_valid_out,
    
    // Host command inputs (Gap 4: USB Read Path, CDC-synchronized)
    // CDC-synchronized in radar_system_top.v before reaching here
    input wire [1:0] host_mode,      // Radar mode: 00=STM32, 01=auto-scan, 10=single-chirp
    input wire host_trigger,          // Single-chirp trigger pulse (1 clk cycle)
    input wire [1:0] host_range_mode, // Range mode: 00=3km (short only), 01=long-range (dual chirp)

    // Gap 2: Host-configurable chirp timing (CDC-synchronized in radar_system_top.v)
    input wire [15:0] host_long_chirp_cycles,
    input wire [15:0] host_long_listen_cycles,
    input wire [15:0] host_guard_cycles,
    input wire [15:0] host_short_chirp_cycles,
    input wire [15:0] host_short_listen_cycles,
    input wire [5:0]  host_chirps_per_elev,

    // Digital gain control (Fix 3: between DDC output and matched filter)
    // [3]=direction: 0=amplify(left shift), 1=attenuate(right shift)
    // [2:0]=shift amount: 0..7 bits. Default 0 = pass-through.
    input wire [3:0] host_gain_shift,

    // AGC configuration (opcodes 0x28-0x2C, active only when agc_enable=1)
    input wire        host_agc_enable,      // 0x28: 0=manual, 1=auto AGC
    input wire [7:0]  host_agc_target,      // 0x29: target peak magnitude
    input wire [3:0]  host_agc_attack,      // 0x2A: gain-down step on clipping
    input wire [3:0]  host_agc_decay,       // 0x2B: gain-up step when weak
    input wire [3:0]  host_agc_holdoff,     // 0x2C: frames before gain-up

    // STM32 toggle signals for mode 00 (STM32-driven) pass-through.
    // These are CDC-synchronized in radar_system_top.v / radar_transmitter.v
    // before reaching this module. In mode 00, the RX mode controller uses
    // these to synchronize receiver processing with STM32-timed chirps.
    input wire stm32_new_chirp_rx,
    input wire stm32_new_elevation_rx,
    input wire stm32_new_azimuth_rx,

    // CFAR integration: expose Doppler frame_complete to top level
    output wire doppler_frame_done_out,

    // Ground clutter removal controls
    input wire        host_mti_enable,       // 1=MTI active, 0=pass-through
    input wire [2:0]  host_dc_notch_width,   // DC notch: zero Doppler bins within ±width of DC

    // AUDIT-C3: AD9484 sign-conversion select (opcode 0x33). Selects DDC
    // sign-conversion to match the SCLK/DFS strap (SJ1) on the Main Board.
    // 2'b00 = offset-binary (default), 2'b01 = two's-complement.
    input wire [1:0]  host_adc_format,

    // AUDIT-S25: AD9484 power-down control (opcode 0x32). Active-high per
    // AD9484 datasheet ("Power-Down (PWDN)" section). 1'b0 = ADC powered up
    // (default), 1'b1 = PWDN asserted. Lets the MCU recover the ADC from a
    // stuck state without dropping main power. Pin drives AD9484 PWDN net via
    // the R36/R37 divider on the Main Board (CMOS thresholds, no level
    // translation needed). Stable single-bit level — no CDC needed.
    input wire        host_adc_pwdn,

    // ADC raw data tap (clk_100m domain, post-DDC, for self-test / debug)
    output wire [15:0] dbg_adc_i,            // DDC output I (16-bit signed, 100 MHz)
    output wire [15:0] dbg_adc_q,            // DDC output Q (16-bit signed, 100 MHz)
    output wire        dbg_adc_valid,        // DDC output valid (100 MHz)

    // AGC status outputs (for status readback / STM32 outer loop)
    output wire [7:0]  agc_saturation_count, // Per-frame clipped sample count
    output wire [7:0]  agc_peak_magnitude,   // Per-frame peak (upper 8 bits)
    output wire [3:0]  agc_current_gain,     // Effective gain_shift encoding

    // DDC overflow diagnostics (audit F-6.1 — previously deleted at boundary).
    // Not yet plumbed into the USB status packet (protocol contract is frozen);
    // exposed here for gpio aggregation and ILA mark_debug visibility.
    output wire        ddc_overflow_any,
    output wire [2:0]  ddc_saturation_count,

    // MTI 2-pulse canceller saturation count (audit F-6.3).
    output wire [7:0]  mti_saturation_count_out,

    // Range-bin decimator watchdog (audit F-6.4 — previously tied off
    // with an ILA-only note). A high pulse here means the decimator
    // FSM has not seen the expected number of input samples within
    // its timeout window, i.e. the upstream FIR/CDC has stalled.
    output wire        range_decim_watchdog,

    // Audit F-1.2: sticky CIC→FIR CDC overrun flag. Asserts on the first
    // silent sample drop between the 400 MHz CIC output and the 100 MHz
    // FIR input; stays high until the next reset. OR'd into the GPIO
    // diagnostic bit at the top level.
    output wire        ddc_cic_fir_overrun
);

// ========== INTERNAL SIGNALS ==========
wire use_long_chirp;
// NOTE: chirp_counter is now an input port (was undriven internal wire — bug NEW-1)
wire chirp_start;
wire azimuth_change;
wire elevation_change;

// Mode controller outputs → matched_filter_multi_segment
wire mc_new_chirp;
wire mc_new_elevation;
wire mc_new_azimuth;

wire [1:0] segment_request;
wire mem_request;
wire [15:0] ref_i, ref_q;
wire mem_ready;

wire [15:0] adc_i_scaled, adc_q_scaled;
wire adc_valid_sync;

// Gain-controlled signals (between DDC output and matched filter)
wire signed [15:0] gc_i, gc_q;
wire gc_valid;
wire [7:0] gc_saturation_count;  // Diagnostic: per-frame clipped sample counter
wire [7:0] gc_peak_magnitude;    // Diagnostic: per-frame peak magnitude
wire [3:0] gc_current_gain;      // Diagnostic: effective gain_shift

// Reference signal for the processing chain (carries long OR short ref
// depending on use_long_chirp — selected by chirp_memory_loader_param)
wire [15:0] ref_chirp_real, ref_chirp_imag;

// ========== DOPPLER PROCESSING SIGNALS ==========
wire [31:0] range_data_32bit;
wire range_data_valid;
wire new_chirp_frame;

// Doppler processor outputs
wire [31:0] doppler_spectrum;
wire doppler_spectrum_valid;
wire [4:0] doppler_bin_out;
wire doppler_processing;

// frame_complete from doppler_processor is a LEVEL signal (high whenever
// state == S_IDLE && !frame_buffer_full). Downstream consumers (USB FT2232H,
// AGC, CFAR) expect a single-cycle PULSE. Convert here at the source so all
// consumers are safe.
wire doppler_frame_done_level;  // raw level from doppler_processor
reg  doppler_frame_done_prev;
wire doppler_frame_done;        // rising-edge pulse (1 clk cycle)

// [RX-E FIX] doppler_frame_done_level is HIGH at reset (state==S_IDLE,
// frame_buffer_full==0). Initializing prev to 1'b0 produces a spurious
// rising-edge pulse on cycle 1, before any real frame has been processed,
// which causes a stale AGC gain update and a phantom CFAR tick. Initialize
// prev to 1'b1 so the first edge fires only after the doppler processor
// actually exits idle for a real frame and returns.
always @(posedge clk or negedge reset_n) begin
    if (!reset_n)
        doppler_frame_done_prev <= 1'b1;
    else
        doppler_frame_done_prev <= doppler_frame_done_level;
end

assign doppler_frame_done = doppler_frame_done_level & ~doppler_frame_done_prev;
assign doppler_frame_done_out = doppler_frame_done;

// ========== RANGE BIN DECIMATOR SIGNALS ==========
wire signed [15:0] decimated_range_i;
wire signed [15:0] decimated_range_q;
wire decimated_range_valid;
wire [`RP_RANGE_BIN_WIDTH_MAX-1:0] decimated_range_bin;  // 9-bit

// ========== MTI CANCELLER SIGNALS ==========
wire signed [15:0] mti_range_i;
wire signed [15:0] mti_range_q;
wire mti_range_valid;
wire [`RP_RANGE_BIN_WIDTH_MAX-1:0] mti_range_bin;  // 9-bit
wire mti_first_chirp;

// ========== RADAR MODE CONTROLLER SIGNALS ==========
wire rmc_scanning;
wire rmc_scan_complete;
wire [5:0] rmc_chirp_count;
wire [5:0] rmc_elevation_count;
wire [5:0] rmc_azimuth_count;

// ========== MODULE INSTANTIATIONS ==========

// 0. Radar Mode Controller — drives chirp/elevation/azimuth timing signals
//    Default mode: auto-scan (2'b01). Change to 2'b00 for STM32 pass-through.
radar_mode_controller rmc (
    .clk(clk),
    .reset_n(reset_n),
    .mode(host_mode),                     // Controlled by host via USB (default: 2'b01 auto-scan)
    .range_mode(host_range_mode),          // Range mode: 00=3km, 01=long-range (drives chirp type)
    .stm32_new_chirp(stm32_new_chirp_rx),
    .stm32_new_elevation(stm32_new_elevation_rx),
    .stm32_new_azimuth(stm32_new_azimuth_rx),
    .trigger(host_trigger),           // Single-chirp trigger from host via USB
    // Gap 2: Runtime-configurable timing from host USB commands
    .cfg_long_chirp_cycles(host_long_chirp_cycles),
    .cfg_long_listen_cycles(host_long_listen_cycles),
    .cfg_guard_cycles(host_guard_cycles),
    .cfg_short_chirp_cycles(host_short_chirp_cycles),
    .cfg_short_listen_cycles(host_short_listen_cycles),
    .cfg_chirps_per_elev(host_chirps_per_elev),
    .use_long_chirp(use_long_chirp),
    .mc_new_chirp(mc_new_chirp),
    .mc_new_elevation(mc_new_elevation),
    .mc_new_azimuth(mc_new_azimuth),
    .chirp_count(rmc_chirp_count),
    .elevation_count(rmc_elevation_count),
    .azimuth_count(rmc_azimuth_count),
    .scanning(rmc_scanning),
    .scan_complete(rmc_scan_complete)
);
wire clk_400m;

// NOTE: lvds_to_cmos_400m removed — ad9484_interface_400m now provides
// the buffered 400MHz DCO clock via adc_dco_bufg, avoiding duplicate
// IBUFDS instantiations on the same LVDS clock pair.

// 1. ADC + CDC + Digital Gain

// CMOS Output Interface (400MHz Domain)
wire [7:0] adc_data_cmos;  // 8-bit ADC data (CMOS, from ad9484_interface_400m)
wire adc_valid;            // Data valid signal

// AUDIT-S25: ADC power-down driven by host_adc_pwdn (opcode 0x32). Default
// 0 keeps the ADC powered up — same behavior as the previous hard-tied 1'b0.
// Set to 1 to assert AD9484 PWDN; see port comment for full design notes.
assign adc_pwdn = host_adc_pwdn;

wire adc_overrange_400m;
ad9484_interface_400m adc (
	.adc_d_p(adc_d_p),
	.adc_d_n(adc_d_n),
	.adc_dco_p(adc_dco_p),
	.adc_dco_n(adc_dco_n),
	.adc_or_p(adc_or_p),
	.adc_or_n(adc_or_n),
	.sys_clk(clk),
	.reset_n(reset_n),
	.adc_data_400m(adc_data_cmos),
	.adc_data_valid_400m(adc_valid),
	.adc_dco_bufg(clk_400m),
	.adc_overrange_400m(adc_overrange_400m)
);

// Audit F-0.1: stickify the 400 MHz OR pulse, then CDC to clk_100m via 2FF.
// Same reasoning as ddc_cic_fir_overrun: single-bit, low→high-only once
// latched, so a 2FF sync is sufficient for a GPIO-class diagnostic. Cleared
// only by global reset_n.
reg adc_overrange_sticky_400m;
always @(posedge clk_400m or negedge reset_n) begin
    if (!reset_n)
        adc_overrange_sticky_400m <= 1'b0;
    else if (adc_overrange_400m)
        adc_overrange_sticky_400m <= 1'b1;
end

(* ASYNC_REG = "TRUE" *) reg [1:0] adc_overrange_sync_100m;
always @(posedge clk or negedge reset_n) begin
    if (!reset_n)
        adc_overrange_sync_100m <= 2'b00;
    else
        adc_overrange_sync_100m <= {adc_overrange_sync_100m[0], adc_overrange_sticky_400m};
end
wire adc_overrange_100m = adc_overrange_sync_100m[1];

// NOTE: The cdc_adc_to_processing instance that was here used src_clk=dst_clk=clk_400m
// (same clock domain — no crossing). Gray-code CDC on same-clock with fast-changing
// ADC data corrupts samples because Gray coding only guarantees safe transfer of
// values that change by 1 LSB at a time. The real 400MHz→100MHz CDC crossing is
// handled inside ddc_400m_enhanced via CIC decimation + CDC_FIR instances.
// Removed: cdc_adc_to_processing instance. ADC data now goes directly to DDC.

// 2. DDC Input Interface
wire signed [17:0] ddc_out_i;
wire signed [17:0] ddc_out_q;

wire ddc_valid_i;
wire ddc_valid_q;

// DDC diagnostic signals (audit F-6.1 — all outputs previously unconnected)
wire [1:0] ddc_status_w;
wire [7:0] ddc_diagnostics_w;
wire       ddc_mixer_saturation;
wire       ddc_filter_overflow;

(* mark_debug = "true" *) wire ddc_mixer_saturation_dbg = ddc_mixer_saturation;
(* mark_debug = "true" *) wire ddc_filter_overflow_dbg  = ddc_filter_overflow;
(* mark_debug = "true" *) wire [7:0] ddc_diagnostics_dbg = ddc_diagnostics_w;

ddc_400m_enhanced ddc(
    .clk_400m(clk_400m),           // 400MHz clock from ADC DCO
    .clk_100m(clk),           // 100MHz system clock //used by the 2 FIR
    .reset_n(reset_n),
    .adc_data(adc_data_cmos),     // ADC data at 400MHz (direct from ADC interface)
    .adc_data_valid_i(adc_valid),     // Valid at 400MHz
    .adc_data_valid_q(adc_valid),     // Valid at 400MHz
    .adc_format(host_adc_format),  // AUDIT-C3: opcode 0x33 selects offset-binary vs 2C
    .baseband_i(ddc_out_i), // I output at 100MHz
    .baseband_q(ddc_out_q), // Q output at 100MHz
    .baseband_valid_i(ddc_valid_i),     // Valid at 100MHz
    .baseband_valid_q(ddc_valid_q),
    .mixers_enable(1'b1),
    // Diagnostics (audit F-6.1) — previously all unconnected
    .ddc_status(ddc_status_w),
    .ddc_diagnostics(ddc_diagnostics_w),
    .mixer_saturation(ddc_mixer_saturation),
    .filter_overflow(ddc_filter_overflow),
    // Test/debug inputs — explicit tie-low (were floating)
    .test_mode(2'b00),
    .test_phase_inc(16'h0000),
    .force_saturation(1'b0),
    .reset_monitors(1'b0),
    .debug_sample_count(),
    .debug_internal_i(),
    .debug_internal_q(),
    .cdc_cic_fir_overrun(ddc_cic_fir_overrun)
);

// Audit F-0.1: AD9484 overrange aggregated here so a single gpio_dig bit
// covers DDC-internal saturation, FIR overflow, AND raw ADC clipping.
assign ddc_overflow_any     = ddc_mixer_saturation | ddc_filter_overflow | adc_overrange_100m;
assign ddc_saturation_count = ddc_diagnostics_w[7:5];

ddc_input_interface ddc_if (
    .clk(clk),
    .reset_n(reset_n),
    .ddc_i(ddc_out_i),
    .ddc_q(ddc_out_q),
    .valid_i(ddc_valid_i),
    .valid_q(ddc_valid_q),
    .adc_i(adc_i_scaled),
    .adc_q(adc_q_scaled),
    .adc_valid(adc_valid_sync),
    .data_sync_error()
);

// 2b. Digital Gain Control with AGC
// Host-configurable power-of-2 shift between DDC output and matched filter.
// Default gain_shift=0, agc_enable=0 → pass-through (no behavioral change).
// When agc_enable=1: auto-adjusts gain per frame based on peak/saturation.
rx_gain_control gain_ctrl (
    .clk(clk),
    .reset_n(reset_n),
    .data_i_in(adc_i_scaled),
    .data_q_in(adc_q_scaled),
    .valid_in(adc_valid_sync),
    .gain_shift(host_gain_shift),
    // AGC configuration
    .agc_enable(host_agc_enable),
    .agc_target(host_agc_target),
    .agc_attack(host_agc_attack),
    .agc_decay(host_agc_decay),
    .agc_holdoff(host_agc_holdoff),
    // Frame boundary from Doppler processor
    .frame_boundary(doppler_frame_done),
    // Outputs
    .data_i_out(gc_i),
    .data_q_out(gc_q),
    .valid_out(gc_valid),
    .saturation_count(gc_saturation_count),
    .peak_magnitude(gc_peak_magnitude),
    .current_gain(gc_current_gain)
);

// 3. Dual Chirp Memory Loader
wire [10:0] sample_addr_from_chain;

chirp_memory_loader_param chirp_mem (
    .clk(clk),
    .reset_n(reset_n),
    .segment_select(segment_request),
    .mem_request(mem_request),
    .use_long_chirp(use_long_chirp),
	 .sample_addr(sample_addr_from_chain),
    .ref_i(ref_i),
    .ref_q(ref_q),
    .mem_ready(mem_ready)
);

// 4. [RX-B FIX, Option A 2026-04-23] Reference chirp wired to MF chain with
// a single-FF alignment delay. Previously ran through `latency_buffer` with
// LATENCY=3187 — that module is a count-N-valid-pulses-then-prime FIFO,
// not a true cycle delay. It needed ~2 frames of mem_request pulses before
// any ref reached the chain (so frame 1 saw all-zero ref → noise output).
// Removed in favour of a direct-wire path with one FF.
//
// Why the 1-FF stage: multi_segment ST_PROCESSING latches `adc_data` through
// one register stage (`fft_input_i <= buf_rdata_i`) before it reaches the
// chain. The ref path from chirp_memory_loader is combinational into the
// chain. Without compensation, ref leads sig by 1 cycle → autocorrelation
// peak at bin 1 instead of bin 0 (verified in tb/tb_rxb_fullchain_latency.v
// against fft_engine.v synthesis path: peak/mean ratio ~80× confirms clean
// correlation; peak position fixed to bin 0 by this register stage).
reg [15:0] ref_chirp_real_d, ref_chirp_imag_d;
always @(posedge clk or negedge reset_n) begin
    if (!reset_n) begin
        ref_chirp_real_d <= 16'd0;
        ref_chirp_imag_d <= 16'd0;
    end else begin
        ref_chirp_real_d <= ref_i;
        ref_chirp_imag_d <= ref_q;
    end
end
assign ref_chirp_real = ref_chirp_real_d;
assign ref_chirp_imag = ref_chirp_imag_d;

// 5. Dual Chirp Matched Filter

wire signed [15:0] range_profile_i;
wire signed [15:0] range_profile_q;
wire range_valid;

// Expose matched filter output to top level for USB range profile
assign range_profile_i_out = range_profile_i;
assign range_profile_q_out = range_profile_q;
assign range_profile_valid_out = range_valid;
// Manhattan magnitude: |I| + |Q|, saturated to 16 bits
wire [15:0] abs_mti_i = mti_range_i[15] ? (~mti_range_i + 16'd1) : mti_range_i;
wire [15:0] abs_mti_q = mti_range_q[15] ? (~mti_range_q + 16'd1) : mti_range_q;
wire [16:0] manhattan_sum = {1'b0, abs_mti_i} + {1'b0, abs_mti_q};
assign decimated_range_mag_out = manhattan_sum[16] ? 16'hFFFF : manhattan_sum[15:0];
assign decimated_range_valid_out = mti_range_valid;

matched_filter_multi_segment mf_dual (
    .clk(clk),
    .reset_n(reset_n),
    .ddc_i({{2{gc_i[15]}}, gc_i}),
    .ddc_q({{2{gc_q[15]}}, gc_q}),
    .ddc_valid(gc_valid),
    .use_long_chirp(use_long_chirp),
    .chirp_counter(chirp_counter),
    .mc_new_chirp(mc_new_chirp),
    .mc_new_elevation(mc_new_elevation),
    .mc_new_azimuth(mc_new_azimuth),
	 .ref_chirp_real(ref_chirp_real),      // 1-FF aligned ref (RX-B fix)
    .ref_chirp_imag(ref_chirp_imag),
    .segment_request(segment_request),
    .mem_request(mem_request),
	 .sample_addr_out(sample_addr_from_chain),
    .mem_ready(mem_ready),
    .pc_i_w(range_profile_i),
    .pc_q_w(range_profile_q),
    .pc_valid_w(range_valid)
);

// ========== CRITICAL: RANGE BIN DECIMATOR ==========
// Convert 2048 range bins to 512 bins for Doppler
range_bin_decimator #(
    .INPUT_BINS(`RP_FFT_SIZE),              // 2048
    .OUTPUT_BINS(`RP_MAX_OUTPUT_BINS),      // 512 (50T) / 4096 (200T)  [RX-D]
    .DECIMATION_FACTOR(`RP_DECIMATION_FACTOR)  // 4
) range_decim (
    .clk(clk),
    .reset_n(reset_n),
    .range_i_in(range_profile_i),
    .range_q_in(range_profile_q),
    .range_valid_in(range_valid),
    .range_i_out(decimated_range_i),
    .range_q_out(decimated_range_q),
    .range_valid_out(decimated_range_valid),
    .range_bin_index(decimated_range_bin),
    .decimation_mode(2'b01),           // Peak detection mode
    .start_bin(11'd0),
    .watchdog_timeout(range_decim_watchdog)  // Audit F-6.4 — plumbed out
);

// ========== MTI CANCELLER (Ground Clutter Removal) ==========
// 2-pulse canceller: subtracts previous chirp from current chirp.
// H(z) = 1 - z^{-1} → null at DC Doppler, removes stationary clutter.
// When host_mti_enable=0: transparent pass-through.
mti_canceller #(
    .NUM_RANGE_BINS(`RP_MAX_OUTPUT_BINS),   // 512 (50T) / 4096 (200T)  [RX-D]
    .DATA_WIDTH(`RP_DATA_WIDTH)             // 16
) mti_inst (
    .clk(clk),
    .reset_n(reset_n),
    .range_i_in(decimated_range_i),
    .range_q_in(decimated_range_q),
    .range_valid_in(decimated_range_valid),
    .range_bin_in(decimated_range_bin),
    .range_i_out(mti_range_i),
    .range_q_out(mti_range_q),
    .range_valid_out(mti_range_valid),
    .range_bin_out(mti_range_bin),
    .mti_enable(host_mti_enable),
    .use_long_chirp(use_long_chirp),
    .mti_first_chirp(mti_first_chirp),
    .mti_saturation_count(mti_saturation_count_out)
);

// ========== FRAME SYNC FROM TRANSMITTER ==========
// [FPGA-001 FIXED] Use the authoritative new_chirp_frame signal from the
// transmitter (via plfm_chirp_controller_enhanced), CDC-synchronized to
// clk_100m in radar_system_top. Previous code tried to derive frame
// boundaries from chirp_counter == 0, but that counter comes from the
// transmitter path (plfm_chirp_controller_enhanced) which does NOT wrap
// at chirps_per_elev — it overflows to N and only wraps at 6-bit rollover
// (64). This caused frame pulses at half the expected rate for N=32.
reg tx_frame_start_prev;
reg new_frame_pulse;

always @(posedge clk or negedge reset_n) begin
    if (!reset_n) begin
        tx_frame_start_prev <= 1'b0;
        new_frame_pulse <= 1'b0;
    end else begin
        new_frame_pulse <= 1'b0;

        // Edge detect: tx_frame_start is a toggle-CDC derived pulse that
        // may be 1 clock wide.  Capture rising edge for clean 1-cycle pulse.
        if (tx_frame_start && !tx_frame_start_prev) begin
            new_frame_pulse <= 1'b1;
        end

        tx_frame_start_prev <= tx_frame_start;
    end
end

assign new_chirp_frame = new_frame_pulse;

// ========== DATA PACKING FOR DOPPLER ==========
// Use MTI-filtered data (or pass-through if MTI disabled)
assign range_data_32bit = {mti_range_q, mti_range_i};
assign range_data_valid = mti_range_valid;

// ========== DOPPLER PROCESSOR ==========
doppler_processor_optimized #(
    .DOPPLER_FFT_SIZE(`RP_DOPPLER_FFT_SIZE),        // 16
    .RANGE_BINS(`RP_MAX_OUTPUT_BINS),               // 512 (50T) / 4096 (200T)  [RX-D]
    .CHIRPS_PER_FRAME(`RP_CHIRPS_PER_FRAME),        // 32
    .CHIRPS_PER_SUBFRAME(`RP_CHIRPS_PER_SUBFRAME)   // 16
) doppler_proc (
    .clk(clk),
    .reset_n(reset_n),
    .range_data(range_data_32bit),
    .data_valid(range_data_valid),
    .new_chirp_frame(new_chirp_frame),
    
    // Outputs
    .doppler_output(doppler_output),
    .doppler_valid(doppler_valid),
    .doppler_bin(doppler_bin),
    .range_bin(range_bin),
    
    // Status
    .processing_active(doppler_processing),
    .frame_complete(doppler_frame_done_level),
    .status()
);

// ========== OUTPUT CONNECTIONS ==========
// doppler_output, doppler_valid, doppler_bin, range_bin are directly
// connected to doppler_proc ports above

// ========== STATUS ==========

// ========== DEBUG AND VERIFICATION ==========
reg [31:0] frame_counter;
reg [5:0] chirps_in_current_frame;

always @(posedge clk or negedge reset_n) begin
    if (!reset_n) begin
        frame_counter <= 0;
        chirps_in_current_frame <= 0;
    end else begin
        // Count chirps in current frame
        if (range_data_valid && decimated_range_bin == 0) begin
            // First range bin of a chirp
            chirps_in_current_frame <= chirps_in_current_frame + 1;
        end
        
        // Detect frame completion
        if (new_chirp_frame) begin
            frame_counter <= frame_counter + 1;
            `ifdef SIMULATION
            $display("[TOP] Frame %0d started. Previous frame had %0d chirps", 
                     frame_counter, chirps_in_current_frame);
            `endif
            chirps_in_current_frame <= 0;
        end
    end
end


// ========== ADC DEBUG TAP (for self-test / bring-up) ==========
assign dbg_adc_i     = adc_i_scaled;
assign dbg_adc_q     = adc_q_scaled;
assign dbg_adc_valid = adc_valid_sync;

// ========== AGC STATUS OUTPUTS ==========
assign agc_saturation_count = gc_saturation_count;
assign agc_peak_magnitude   = gc_peak_magnitude;
assign agc_current_gain     = gc_current_gain;

endmodule