C-4: GUI Waveform Timing opcodes (0x10..0x14) write one parameter per
USB packet with arbitrary inter-opcode latency. Previously each opcode
landed directly on a live register consumed by radar_mode_controller,
so a mid-scan reconfiguration exposed the RX FSM to torn sets (e.g.
new long_chirp with old long_listen), and a value below the running
timer truncated the current chirp and corrupted one range-Doppler
frame.
Fix: split each of the five timing regs into pending (USB write target)
and live (FSM consumer). radar_mode_controller exports a new
cfg_commit_strobe that is HIGH while scanning is idle (S_IDLE) and
pulses for 1 cycle at every elevation/azimuth boundary in S_ADVANCE.
radar_system_top snapshots pending -> live on the strobe, guaranteeing
the FSM always sees a self-consistent set. No CDC added: strobe is in
clk_100m same as the USB-cmd path.
Regression: tb_radar_mode_controller adds 3 checks for strobe
semantics (idle-HIGH, scanning-LOW, one pulse per elevation boundary).
32/32 full regression PASS; Radar Mode Controller TB grows from 78 to
81 checks.
RTL (P0 pre-bringup findings R-1/R-2/R-3/R-5/R-6):
- mti_canceller: add use_long_chirp input and waveform-boundary mute
so the long->short transition in mode 01 no longer subtracts across
heterogeneous waveforms (R-1). Prev buffer is overwritten in-flight
at the boundary so the next same-waveform chirp subtracts cleanly.
- ad9484_interface_400m: 2FF sync of mmcm_locked into the 400 MHz
domain before gating reset_n_gated (R-6).
- cic_decimator_4x_enhanced: correct max_fanout narrative (R-3).
- ad9484_interface_400m: strip stale pblock comment, note 3.0 ns
max_delay instead (R-2).
- mti_canceller / doppler_processor: 200T-20km WARNING banners
flagging the broken 4096-bin path (R-5). 9-bit BRAM address aliases
silently until rewritten.
- adc_clk_mmcm.xdc: relax set_max_delay from 2.700 -> 3.000 ns,
closes WNS with headroom on 50T build.
- radar_receiver_final: wire use_long_chirp into mti_inst.
Architecture-bump finalization (2048-pt range FFT, 512 range bins,
32 Doppler bins -> 16384 output cells per frame):
- tb/cosim/radar_scene.py: FFT_SIZE 1024 -> 2048, RANGE_BINS 64 -> 512.
- tb/gen_mf_golden_ref.py: N 1024 -> 2048.
- Regenerate all affected hex goldens (MF cases 1-4, Doppler inputs
+ py goldens, receiver integration golden_doppler.mem 2048 -> 16384).
- tb_radar_receiver_final: widen range_bin_out 6 -> 9 bits, bump
GOLDEN_ENTRIES 2048 -> 16384, expand bitmaps/arrays to 512 bins,
update all check messages and thresholds.
- tb_mti_canceller, tb_fullchain_mti_cfar_realdata: tie/pass
use_long_chirp so compile still works after RTL port add.
Test-suite hardening (coverage audit findings):
- tb_mti_canceller T12: 10 new assertions exercising R-1 waveform-
boundary mute across a long/long/short/short/long sequence. Catches
a regression that re-enables subtraction across the boundary.
- tb_fir_lowpass: replace tautological check(1'b1, ...) on coefficient
symmetry with a real hierarchical check coeff[k]===coeff[31-k];
replace always-pass overflow check with a well-driven (not X/Z)
assertion on filter_overflow.
- tb_matched_filter_processing_chain: replace three always-pass peak-
bin placeholders with peak-to-mean-|out| > 2x ratio checks (catches
flat/zero output that the old tautologies silently accepted).
- tb_cdc_modules M2: replace always-pass narrow-pulse check with a
well-defined-output assertion on the synchronizer.
- tb_nco_400m: replace always-pass freq-switch check with a swing +
no-X assertion across 200 post-switch samples.
- tb_system_e2e G12.1: replace check(1, ...) with test_num > 20 so
it catches a stalled TB that skipped prior groups.
- tb_multiseg_cosim TEST 4: replace always-pass placeholder with a
bitmap that asserts segment_request visited all 4 values.
- tb_mf_chain_synth and tb_fullchain_mti_cfar_realdata: add DEPRECATED
headers plus \$fatal guards (ifndef ALLOW_STALE_*) so they cannot
be silently re-enabled in CI with stale 1024-bin goldens against
current 2048-pt RTL.
Regression: 32 passed, 0 failed. MTI TB grew 30 -> 39 checks;
receiver integration grew 17 -> 18 checks with 16384/16384 golden
match at tolerance +/- 2 LSB.
Hand-merged files modified on both fix/pre-bringup-audit-p0 and
feat/fft-2048-upgrade. Wave 1 (commit 60e49c7) took 20 files from fft
verbatim; this wave resolves the overlap.
- run_regression.sh: 3-way merge. Adopts fft's ${RECEIVER_RTL[@]} array
refactor and drops the self-blessing golden pair from p0. Skip count
bumped to 5.
- usb_data_interface.v (FT601/200T): p0 FSM + clock-loss watchdog kept
wholesale; widened stream_control 3 -> 6 bits to carry fft's extended
mode bits through the CDC sync chain and the 0xFF status word.
- mti_canceller.v: fft's BRAM-inferred 512-range-bin implementation as
the base, with p0's F-6.3 saturation counter grafted onto the d1
pipeline stage. Overflow detection uses the top-two-bits disagreement
on diff_{i,q}_full (DATA_WIDTH+1 signed).
- radar_receiver_final.v: fft's 2048-pt / 512-bin structure + p0
diagnostic plumbing (ADC overrange sticky+CDC, DDC diagnostics,
tx_frame_start edge detector replacing chirp_counter frame sync,
mti_saturation_count, range_decim_watchdog).
- radar_system_top.v: clean 3-way merge, orthogonal regions
(+38 / -27).
- usb_data_interface_ft2232h.v (FT2232H/50T): fft's per-frame bulk BRAM
rewrite kept wholesale. Ported two p0 items that are orthogonal to
the write FSM:
* ft_clk-loss watchdog (heartbeat + 2FF ASYNC_REG sync + 16-bit
timeout) ORed into a 2FF sync'd ft_effective_reset_n for the FSM.
* rd_cmd_complete flag so RD_DEASSERT can distinguish a legitimate
3-byte completion from an ft_rxf_n abort that also zeros
rd_byte_cnt.
Deliberately NOT taken from 2401f5f: cic_decimator_4x_enhanced.v and
ddc_400m.v reset-strategy changes. Those conflict with p0's shipped
registered-sync-reset + max_fanout=25 distribution, which is already
timing-clean on the production build.
The AD9484 OR (overrange) LVDS pair is routed on the 50T main board to
xc7a50t-ftg256 bank-14 pins M6/N6 but was previously left unconnected at
the top level. Plumb it through the full stack so saturation at the raw
ADC boundary shows up in the existing overflow aggregation:
- ad9484_interface_400m: add adc_or_p/n inputs, IBUFDS + IDDR capture of
both phases in the BUFIO domain, re-register into the clk_400m BUFG
domain, OR rise|fall into adc_overrange_400m output.
- radar_receiver_final: stickify adc_overrange_400m in clk_400m, CDC to
clk_100m via a 2FF ASYNC_REG chain (same reasoning as F-1.2's
cdc_cic_fir_overrun — single-bit, latched low→high, GPIO-class
diagnostic), OR into the existing ddc_overflow_any aggregation.
- radar_system_top: expose adc_or_p/n top-level ports and pass through.
- xc7a50t_ftg256.xdc: anchor M6/N6 as LVDS_25 DIFF_TERM, with the same
DCO-relative input-delay constraints as adc_d_p[*].
- xc7a200t_fbg484.xdc: IOSTANDARD/DIFF_TERM set; PACKAGE_PIN left as a
documented TODO — the 200T dev-board schematic has not been checked
and the 200T build will need the anchor filled in before place/route.
Addresses the remaining actionable items from
docs/DEVELOP_AUDIT_2026-04-19.md after commit 3f47d1e.
XDC (dead waivers — F-0.4, F-0.5, F-0.6, F-0.7):
- ft_clkout_IBUF CLOCK_DEDICATED_ROUTE now uses hierarchical filter;
flat net name did not exist post-synth.
- reset_sync_reg[*] false-path rewritten to walk hierarchy and filter
on CLR/PRE pins.
- adc_clk_mmcm.xdc ft601_clk_in references replaced with foreach-loop
over real USB clock names, gated on -quiet existence.
- MMCM LOCKED waiver uses REF_PIN_NAME filter instead of the
previously-missing u_core/ literal path.
CDC (F-1.1, F-1.2, F-1.3):
- Documented the quasi-static-bus stability invariant above the
FT601 cmd_valid toggle block.
- cdc_adc_to_processing gains an `overrun` output; the two CIC->FIR
instances feed a sticky cdc_cic_fir_overrun flag surfaced on
gpio_dig5 so silent sample drops become visible to the MCU.
- Removed the dead mixers_enable synchronizer in ddc_400m.v; the _sync
output was unused and every caller ties the port to 1'b1.
Diagnostics (F-6.4):
- range_bin_decimator watchdog_timeout plumbed through receiver
and top-level, OR'd into gpio_dig5.
ADAR (F-4.7):
- delayUs() replaced with DWT cycle counter; self-initialising
TRCENA/CYCCNTENA, overflow-safe unsigned subtraction.
Regression: tb_cdc_modules.v 57/57 passes under iverilog after
the cdc_modules.v change. Remote Vivado verification in progress.
Addresses findings from docs/DEVELOP_AUDIT_2026-04-19.md:
P0 source-level:
- F-4.3 ADAR1000_Manager::adarSetTxPhase now writes REG_LOAD_WORKING
with LD_WRK_REGS_LDTX_OVERRIDE (0x02) instead of 0x01. Previous value
toggled the LDRX latch on a TX-phase write, so host TX phase updates
never reached the working registers.
- F-6.1 DDC mixer_saturation / filter_overflow / diagnostics were deleted
at the receiver boundary. Now plumbed to new outputs on
radar_receiver_final (ddc_overflow_any, ddc_saturation_count) and
aggregated into gpio_dig5 in radar_system_top. Added mark_debug
attributes for ILA visibility. Test/debug inputs tied low explicitly.
- F-0.8 adc_clk_mmcm.xdc set_clock_uncertainty: removed invalid -add
flag (Vivado silently rejected it, applying zero guardband). Now uses
absolute 0.150 ns which covers 53 ps jitter + ~100 ps PVT margin.
P1:
- F-4.2 adarSetBit / adarResetBit reject broadcast=ON — the RMW sampled
a single device but wrote to all four, clobbering the other three's
state.
- F-4.4 initializeSingleDevice returns false and leaves initialized=false
when scratchpad verification fails; previously marked the device
initialized anyway so downstream PA enable could drive a dead bus.
- F-6.2 FIR I/Q filter_overflow ports, previously unconnected, now OR'd
into the module-level filter_overflow output.
- F-6.3 mti_canceller exposes 8-bit saturation counter. Saturation was
previously invisible and produces spurious Doppler harmonics.
Verification:
- 27/27 iverilog testbenches pass
- 228/228 pytest pass (cross-layer contract + cosim)
- MCU unit tests 51/51 + 24/24 pass
- Remote Vivado 2025.2 build: bitstream writes; 400 MHz mixer pipeline
now shows WNS -0.109 ns which MATCHES the audit's F-0.9 prediction
that the design only closed because F-0.8's guardband was silently
dropped. ft_clkout F-0.9 remains a show-stopper (requires MRCC pin
move), tracked separately.
Not addressed in this PR (larger scope, follow-up tickets):
F-0.4, F-0.5, F-0.6, F-0.7, F-0.9, F-1.1, F-1.2, F-2.2, F-3.2, F-4.1,
F-4.7, F-6.4, F-6.5.
FPGA-001: The previous fix derived frame boundaries from chirp_counter==0,
but that counter comes from plfm_chirp_controller_enhanced which overflows
to N (not wrapping at chirps_per_elev). This caused frame pulses only on
6-bit rollover (every 64 chirps) instead of every N chirps. Now wires the
CDC-synchronized tx_new_chirp_frame_sync signal from the transmitter into
radar_receiver_final, giving correct per-frame timing for any N.
STM32-004: Changed ad9523_init() failure path from Error_Handler() to
return -1, matching the pattern used by ad9523_setup() and ad9523_status()
in the same function. Both halt the system, but return -1 keeps IRQs
enabled for diagnostic output.
STM32-006: Remove blocking do-while loop that waited for legacy GUI start
flag — production V7 PyQt GUI never sends it, hanging the MCU at boot.
STM32-004: Check ad9523_init() return code and call Error_Handler() on
failure, matching the pattern used by all other hardware init calls.
FPGA-001: Simplify frame boundary detection to only trigger on
chirp_counter wrap-to-zero. Previous conditions checking == N and == 2N
were unreachable dead code (counter wraps at N-1). Now correct for any
chirps_per_elev value.
- Remove xfft_32.v, tb_xfft_32.v, and fft_twiddle_32.mem (dead code
since PR #33 moved Doppler to dual 16-pt FFT architecture)
- Update run_regression.sh: xfft_16 in PROD_RTL, remove xfft_32 from
EXTRA_RTL and all compile commands
- Update tb_fft_engine.v to test with N=16 / fft_twiddle_16.mem
- Update validate_mem_files.py: validate fft_twiddle_16.mem instead of 32
- Update testbenches and golden data from main_cleanup branch to match
dual-16 architecture (tb_doppler_cosim, tb_doppler_realdata,
tb_fullchain_realdata, tb_fullchain_mti_cfar_realdata, tb_system_e2e,
radar_receiver_final, golden_doppler.mem)
- Update CONTRIBUTING.md with full regression test instructions covering
FPGA, MCU, GUI, co-simulation, and formal verification
Regression: 23/23 FPGA, 20/20 MCU, 57/58 GUI, 56/56 mem validation,
all co-sim scenarios PASS.
MTI canceller (2-pulse, H(z)=1-z^{-1}) between range decimator and
Doppler processor. Subtracts previous chirp from current, nulling DC
Doppler (stationary clutter). Pass-through when host_mti_enable=0.
DC notch filter (post-Doppler, pre-CFAR) zeros bins within
+/-host_dc_notch_width of DC. Complements MTI for residual clutter.
New host registers: 0x26 (mti_enable), 0x27 (dc_notch_width).
Both default to 0 (disabled) - fully backward-compatible.
Verification: 23/23 regression, 29/29 MTI standalone, 3/3 real-data
co-sim (5137/5137 exact match) all PASS.
RTL fixes discovered via new end-to-end testbench:
- plfm_chirp_controller: TX/RX mixer enables now mutually exclusive
by FSM state (Fix#4), preventing simultaneous TX+RX activation
- usb_data_interface: stream control reset default 3'b001 (range-only),
added doppler/cfar data_pending sticky flags, write FSM triggers on
range_valid only — eliminates startup deadlock (Fix#5)
- radar_receiver_final: STM32 toggle signals wired through for mode-00
pass-through, dynamic frame detection via host_chirps_per_elev
- radar_system_top: STM32 toggle signal wiring to receiver instance
- chirp_memory_loader_param: explicit readmemh range for short chirp
Test infrastructure:
- New tb_system_e2e.v: 46 checks across 12 groups (reset, TX, safety,
RX, USB R/W, CDC, beam scanning, reset recovery, stream control,
latency budgets, watchdog)
- tb_usb_data_interface: Tests 21/22/56 updated for data_pending
architecture (preload flags, verify consumption instead of state)
- tb_chirp_controller: mixer tests T7.1/T7.2 updated for Fix#4
- run_regression.sh: PASS/FAIL regex fixed to match only [PASS]/[FAIL]
markers, added E2E test entry
- Updated rx_final_doppler_out.csv golden data
P0-1: nco_400m_enhanced.v — DSP48E1 OPMODE corrected from PCIN to P
feedback (was routing stale cascade data into accumulator)
P0-2: radar_receiver_final.v — removed same-clock CDC that corrupted
ADC data path between ad9484_interface and DDC
P1-5: fir_lowpass.v — fixed zero replication count in coefficient
symmetric extension ({0{1'b0}} is empty, now uses explicit 0)
Also updates .gitignore to exclude debug/scratch artifacts.
All 30+ testbenches pass (unit, co-sim, integration).
RTL fix: matched_filter_multi_segment.v ST_WAIT_FFT now waits for
processing chain to complete ALL 1024 outputs and return to IDLE
before advancing to next segment. Previously, it transitioned on the
first fft_pc_valid edge, causing the chain to still be outputting
while multi-seg started collecting data for the next segment. This
broke the handshake and caused permanent deadlock after segment 0.
Also fixes forward reference of sample_addr_from_chain in
radar_receiver_final.v (declaration moved before first use).
New files:
- tb/tb_radar_receiver_final.v: P0 integration test for full RX
pipeline (ADC->DDC->MF->range_bin_decimator->doppler), 10 checks
- tb/ad9484_interface_400m_stub.v: behavioral ADC stub for iverilog
All existing tests still pass: multi-seg 32/32, MF co-sim 3/3,
Doppler co-sim 14/14.
